665 Arc-Shaped Single Layer Roll Forming Machine
Contact HUANUO for Shipping, delivery, and payments information.
Products Category
Tag list
- 产品描述
-
Product Parameters
WEIGHT 4222KG VOLUME 13000*1500*1200MM FEED WIDTH 914MM MOLDING WIDTH 665MM SHEET THICKNESS 0.4-0.8MM EXIT SPEED ABOUT8-15M/MIN DRIVE SYSTEM MOTOR DRIVE TRANSMISSION TYPE CHAIN DRIVE ROW NUMBER 24 MOTOR POWER 5.5KW HYDRAULIC POWER 5.5KW CUTTING TYPE 4-GUIDE SHEAR Advantages of Arc-shaped Single-layer Edge Rolling Machines
1. High forming accuracy and uniform curvature
●Continuous rolling through precisely controlled rollers can form very smooth and consistent arcs, avoiding the unevenness or local deformation that may occur during manual forming.
2. High production efficiency
●Once the equipment is debugged, it can continuously and rapidly produce workpieces of the same curvature, which is very suitable for mass production and greatly improves production efficiency.
3. Wide adaptability of materials
●By replacing the rollers or adjusting the parameters, plates of different materials (such as carbon steel, stainless steel, aluminum, and copper), different thicknesses (within the machine's capacity), and different widths can be processed.
4. It will not damage the surface of the material
●It belongs to cold working technology. The roller and the material surface are in rolling contact, causing minimal damage to the coating, plating or the material itself on the sheet surface, thus maintaining the aesthetic appearance and anti-corrosion performance of the workpiece.
5. The operation is relatively safe
●Compared with stamping and other equipment, its working principle is more gentle. The operator's hands do not need to enter the dangerous area of the mold, making it safer.
6. Good flexibility
●By adjusting the gap between the upper and lower rollers and the relative position of the lower roller, arc-shaped workpieces with different radii of curvature can be produced on the same machine without the need to change molds.
7. Save costs
●Low mold cost: There is no need to customize expensive stamping dies for each curvature and plate thickness.
●Low labor cost: High degree of automation, relatively low requirements for the skills of operators.
●High material utilization rate: It reduces the scrap rate caused by mold testing or manual errors.
Preparation before operation
1. Read the equipment manual: Fully understand the performance parameters, operation norms and warning matters of the specific model of the machine.
2. Safety Inspection
●Check whether all components of the equipment are in good condition and whether the fasteners are loose.
●Check the lubrication system to ensure that there is sufficient oil at each lubrication point.
●Make sure the emergency stop button is functioning properly.
3. Personal protection: Operators must wear protective gloves to prevent cuts to the edges of the boards.
4. Material Preparation
●Confirm whether the material, thickness and width of the sheet to be processed are within the processing range of the machine.
●Check the surface of the sheet to ensure there is no welding slag, hard objects, etc., to avoid damaging the roller.
5. Equipment Adjustment (Key Steps) :
●Adjust the gap between the upper roller and the lower roller according to the thickness of the sheet: Set the gap between the upper roller and the lower roller slightly less than the thickness of the sheet through the control system or handwheel to ensure sufficient bending force.
●Adjust the position of the lower roller according to the target curvature: For machines with adjustable lower rollers, it is necessary to precisely adjust the inclination Angle or position of the lower rollers on both sides according to the required radius of curvature. The greater the arc (the smaller the radius of curvature), the more inclined the lower roller needs to be adjusted. Usually, it is necessary to refer to the parameter table that comes with the machine or make fine adjustments through test pieces.
Product Layout Diagram
About Us
● 20+ years of professional roll forming machine manufacturing
● Exported to 100+ countries with global service network
● Strong design team supporting customized profiles and special requirements
● High-quality materials and precision manufacturing process
● Wide range of machines for construction, automotive, and industrial applications
● Continuous R&D and technological innovation
Why Choose Us
● Complete testing and inspection before delivery
● Lifetime technical support and remote assistance
● Onsite installation and commissioning service available
● Competitive pricing with reliable performance
● Customized solutions for different production needs
● Professional after-sales service team
● Quick response to customer inquiries and requirements
Factory
Certificate
Our Partner
Contact Us
665 Arc-Shaped Single Layer Roll Forming Machine
Email:
jacky@huanuomachinery.com
Contact HUANUO for Shipping, delivery, and payments information.
Share to
Tag list
Related Products
We look forward to working with you to jointly promote the development of China's cold bending equipment industry.
Phone/WhatsApp
Send E-mail
Leave Message
For more information, please leave your message below.
Online Message